抢购热线 158-9996-3239
| 物理性能 | 额定值 (公制) | 额定值 (英制) | 测试方法 |
|---|---|---|---|
| 密度 |
1.14 g/cc
@Thickness 2.00 mm
|
0.0412 lb/in³
@Thickness 0.0787 in
|
molded plaque, cured 20 hr at 100°C; ASTM D792 |
| 机械性能 | 额定值 (公制) | 额定值 (英制) | 测试方法 |
|---|---|---|---|
| 肖氏硬度 (邵氏 A) |
75
@Thickness 2.00 mm
|
75
@Thickness 0.0787 in
|
molded plaque, cured 20 hr at 100°C; ASTM D2240 |
| 极限抗拉强度 |
41.0 MPa
@Thickness 2.00 mm
|
5950 psi
@Thickness 0.0787 in
|
molded plaque, cured 20 hr at 100°C; ASTM D412 |
| 抗张强度(屈服) |
4.80 MPa
@Strain 100 %
|
696 psi
@Strain 100 %
|
ASTM D-412 |
|
11.0 MPa
@Strain 300 %
|
1600 psi
@Strain 300 %
|
0.76 mm (0.030 in) extruded sheet; ASTM D-412 | |
| 伸长率 (断裂) | 685 % | 685 % | on 0.030 in extruded sheet; ASTM D-412 |
| 弯曲模量 |
0.0250 GPa
@Thickness 2.00 mm
|
3.63 ksi
@Thickness 0.0787 in
|
molded plaque, cured 20 hr at 100°C; ASTM D790 |
| 撕裂强度 |
27.0 kN/m
@Thickness 0.760 mm
|
154 pli
@Thickness 0.0299 in
|
Split tear strength; extruded sheet; ASTM D-1938 |
| Graves Tear Strength |
57.0 kN/m
@Thickness 0.762 mm
|
325 pli
@Thickness 0.0300 in
|
extruded sheet; ASTM D624 |
| 泰伯磨损，毫克/1000次 |
20
@Thickness 2.00 mm
|
20
@Thickness 0.0787 in
|
H-18 wheel; ASTM D-1044; molded plaque, cured 20 hr at 100°C. |
| 永久压缩 | 25 % | 25 % | 22 hr at 23°C per ASTM D-395; 2.0 mm (0.080 in) molded plaque, cured 20 hr at 100°C. |
|
45 %
@Temperature 70.0 °C
|
45 %
@Temperature 158 °F
|
22 hr @ 70°C; ASTM D-395; 0.080 in molded plaque after curing 20 hrs at 100°C. | |
| Tensile Set | 32 % | 32 % | at 200% elongation per ASTM D-412 is on 0.030 in extruded sheet. |
| 热性能 | 额定值 (公制) | 额定值 (英制) | 测试方法 |
|---|---|---|---|
| 维卡软化温度 |
80.0 °C
@Thickness 2.00 mm
|
176 °F
@Thickness 0.0787 in
|
molded plaque, cured 20 hr at 100°C.; ASTM D1525 |
| 玻璃化转变温度，Tg | -47.0 °C | -52.6 °F | Pellet sample |
| 可燃性(UL94) |
V-2
@Thickness 1.59 mm
|
V-2
@Thickness 0.0626 in
|
Color: NC |
|
V-2
@Thickness 3.14 mm
|
V-2
@Thickness 0.124 in
|
Color: NC | |
|
V-0
@Thickness 0.900 mm
|
V-0
@Thickness 0.0354 in
|
Color: NC |
